The cooker does not require regular servicing, but has been designed so that internal components are
easy to replace in the event that they become faulty.
It is preferable that access to internal parts is made by lifting off the hob.
All the oven and grill elements can be removed and replaced from the front of the cooker through the
oven openings.
To Remove the Base Element from the Bottom Oven
1. Remove the shelves and shelf supports from the oven.
2. Remove the two screws holding down the oven base at each side. Remove the base.
3. Undo the screw fastening the element to the side of the oven. The element can then be pulled out of
the base of the oven. The electrical wire connections should stay attached to the element as it is
pulled from the oven. The element wire terminals can then be swapped from the faulty element to the
new element. Take care not to let the element wire connections fall back inside the cooker before
they are reconnected to the new element.
To Remove the Upper Elements/Grill Element from the Top or Bottom Oven
1. Undo the single screw fastening the element to the side of the oven.
2. Loosen the screws on the element support brackets. The support brackets can then be rotated clear
of the elements allowing the elements to fall.
3. The electrical wire connections should stay attached to the element as it is lowered. The element wire
terminals can then be swapped from the faulty element to the new one. Take care not to let the
element wire connections fall back inside the cooker before they are reconnected to the new
element.
To Remove the Fan Unit from the Main Oven
Unscrew the six screws around the unit, pull the unit out with the wires attached, being careful not to
allow them to fall back into the oven. Remove the fan guard by unscrewing the fixing screws on the top
and two on the bottom of the unit.
To Remove the Induction Elements
Lift off the top.
Unbolt the 6 bolts holding the Induction support panel carefully. Each Induction coil will lift out.
To Replace the Element
Undo the 3 screws holding it, insert new element and replace wires.
To Replace the Motor
Unscrew the fan blade nut, unbolt the 3 fixing bolts, replace motor ensuring the spacing nuts and
wires are correct!
SERVICING INSTRUCTIONS
Isolate the electrical supply before any repair work.
UNPACKING
CONTENTS
The cooker Data Plate is located inside the right hand side lower oven door.
After unpacking the cooker, remove all the packing from the top and bottom ovens including protective
film on door liners. Examine the cooker for any damage, particularly to the hob glass.
If there is any damage to the cooker or anything is missing, please contact your supplier for advice.
If the hob is cracked the cooker must not be connected, and no part of it may be used.
TECHNICAL DATA
ESSE, ENGLAND
ESSE, ENGLANDESSE, ENGLAND
ESSE, ENGLAND
45A
45A45A
45A
ESSE, ELECTRIC
ESSE, ELECTRICESSE, ELECTRIC
ESSE, ELECTRIC
-
--
-
250V
250V250V
250V
50 Hz a.c.
50 Hz a.c.50 Hz a.c.
50 Hz a.c.
VOLTAGE
VOLTAGEVOLTAGE
VOLTAGE
SUPPLY
SUPPLYSUPPLY
SUPPLY
MODEL
MODELMODEL
MODEL
SERIAL No.
SERIAL No.SERIAL No.
SERIAL No.
INPUT
INPUTINPUT
INPUT
Hob Touch Controls Page 9
Before Cooking Page 15
Cleaning Page 15
Servicing Instructions Page 16
Wiring Diagram Page 17
Operating Instructions Page 11
Technical Data Page 3
Unpacking Page 3
Your Cooker Page 4
Spacing & Dimensions/Extraction Page 5
Connecting the Cooker Page 6
Ovens & Grill Page 6
Induction Hob Page 9
15 2
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce